Pistons aren’t round

An article that explains why pistons aren’t round. Click on piston to open it:

Saddle Y-frames R25/2 – R27 and R51/2 – R68

  4 versions of the saddle Y-frames are available: P/N 52 51 7 002 164:   R51/2 – R68      with 8 mm holes for saddle bearing bolt 52 51 7 002 125.7 P/N 52 51 7 002 165:   R51/3 – R68      with 10 mm holes for silent block 52 51 7 002 141 P/N 52 51 7 002 115:   R25/2                 with 8 mm holes for saddle bearing bolt 52 51 7 002 125.7 P/N 52 51 7 002 116:   R25/3 – R27      with 10 mm holes for silent block 52
Read more »

Rim width

The width of rims can be measured in 2 different ways: the inside or the outside. This means that one and the same rim can be indicated both in (for example) 2.15 “and 3.00”    

BING jets

BING jets are stamped with numbers, such as 35, 40 (idle jets) and 110, 115, 120 etc (main jets). One would expect that these numbers refer to the diameter of the jet bore, however this is not the case. This is confimed by the company BING in Germany. A few examples of main jets measured with a wire / jet gauge: BING 44-051 main jet 130 = gauge 120 (= 1.2 mm) main jet 125 = gauge 110 (= 1.1 mm) main jet 120 = gauge 105 (= 1.05 mm) main jet 110 = gauge 95 (=0.95 mm)            
Read more »

Matra 282 tool

We mill 2 planes on the threaded bushing so that it is possible to use a 22 mm wrench on the threaded bushing. This is necessary in cases where (for instance) the crankshaft bearing is glued to the bearing journal, to prevent the threaded bushing from rotating while tightening the central bolt

Exhaust pipes

Different exhaust pipes are available in the market, unfortunately not always an exact replica of the original pipes: the shape of the bends does not correspond with the original BMW exhaust pipes as can be seen on this picture. The 2 lower exhaust pipes are identical to the original pipes    some of these pipes follow a slightly different path than the original exhaust pipes. This causes a problem for the R67 – R67/3 models: in the horizontal section, they’re not running close enough to the frame, causing too little clearance between the brake pedal and the right-hand exhaust pipe, as
Read more »

Carburetor reconditioning

With hardly any new carburetors being produced by BING for the < 1969 BMW mono and twin motorcycles, it’s getting increasingly important to be able to repair and recondition the used original carburetors. Luckily, special parts and tools are available nowadays to restore the carburetors to a good working condition. A. Idle mix screw: very often, the M7 x 0.75 mm screw thread in the carburetor housing is worn out. There are 2 good solutions to this problem. 1. drill the threaded hole to 7.2 mm – cut M8 x 0.75 mm screw thread – install the idle mix screw with
Read more »

Driving dog R51/2 – R68

Part nr: 33120026232 Next to the original BMW driving dog, an after-market version is available in the market. At first view, the after-market product gives the impression of high quality machining. However, there are at least 2 flaws: 1. the geometry of the splines:the splines of the after-market part almost have a V shape instead of the trapezium shape on the original part. This V-shape is normally seen on worn splines 2. The diameter of the needle bearing seat measures 39.94 mm whereas the original parts measures 39.97 mm. This will result in too much play on the needle bearing The
Read more »