Menu

Recommended press fitting for valve seat inserts in aluminum cylinder heads: OD insert 30 – 40 mm: 0.15 mm / 0.0059″ OD insert 40 – 50 mm: 0.18 mm / 0.0071″   Spindle speed for cutting a seat pocket in aluminum cylinder heads: 400 – 600 rpm It’s recommended NOT to freeze (f.i. with liquid nitrogen) the sintered valve seat inserts before installation. The valve seats are to be pressed in with a flat and square seat driver tool. The valve seat is inserted with the radius side down.   Source: DuraBond

By Richard Sheckler, Wayne, Ohio A tool that can be used to accurately and squarely install and press fit the atomizer in place without damage. The replacement part has a different size knurling than the original, and therefore has sufficient resistance to remain in place for a long time.    

There is a clear length difference between the side stands for the R50 – R69S models and the R50US, R60US and R69US models (due to different configurations of the front fork) These are therefore not interchangeable.

All Matra tools with spindles such as M355, M499 / 1/2, M422a, M501 and M282 work much better (more smoothly) if a small amount of lubricant (eg Molykote G-n Metal Assembly Paste) is applied to the thread. This prevents galling of the thread under heavy load and reduces, to a certain extent, unwanted rotation of the other part of the tool.

Click here for installation instructions 12V dynamo system VAPE: Dynamo System 70 80 499 0XX

If you are working on the overhaul of a 2 cylinder engine block with the old 1 or 2 pin breather plate, it is advisable to replace it with the later version with cast-in pins The pins of the early 1 or 2 pin breather plates are known for loosening or breaking off, causing damage to gear case cover. However, this means that the complete set of gears must be replaced (from 20° to 30° gears) The breather plate of the newer version is also available with larger slots, reducing pressure in the engine block during the downward movement of
Read more »

The width of rims can be measured in 2 different ways: the inside or the outside. This means that one and the same rim can be indicated both in (for example) 2.15 “and 3.08″ WM2: inside 1.85″ (47 mm) outside 2.72″ (69 mm) WM3: inside 2.15″ (55 mm) outside 3.08” (78.2 mm)      

For the correct set, check the number marked in the crankcase. The number is found near the upper engine mount, see following examples: In some cases, when the engine has had a long service life, it may need a different gear set number to get the required 0.02 mm clearance. However, this can only be determined through an accurate measurement.   The 30° gear set can be used to replace the 20° gear set on all 1950 to 1963 models. This requires following additional parts: › part nr. 11410052156 – oilpump gear 30° Only for crankshaft with 17 mm taper: › part nr. 11310016400 – 1.5
Read more »

These posters are only shown for information. We do not sell these posters. We welcome BMW posters from the pre-69 era.  Mail us at  info@salisparts.com    

The R50 – R69S dual cable throttle assembly cannot be simply converted to a R26, R27 single cable throttle assembly by replacing the cam & chain and the cover. The depth of the recess in single cable cam and dual cable cams differs. The mono cam will not sit deep enough to engage with the throttle twist grip. Vice versa: the dual cable cam will not fit in the single throttle cable assembly: it’s too high.

A frequently asked question is how to fix a leakage of the idle mixing screw. Further tightening the nut of the idle mix screw is certainly not the solution: holes have been drilled in the idle mix screw which connects the idle mix chamber to the the outside air. If fuel leaks out through the same bore, it simply means that the fuel level in the float bowl is too high. (assuming that the bike is on the center stand, if the motorcycle is placed on the side stand, there is a greater risk of leakage) If the carbs keep leaking, it’s
Read more »

By Michel Loos, The Netherlands The photos are self-explanatory. Steps:  filing  – sanding – pneumatic hammer – aluminum oxide blasting (Edelkorund) – glass bead blasting